Lead Removal / Heavy Metals
Reduce lead and heavy metals at the source with Woder’s under-sink filters – direct-connect install, no drilling required.
Showing all 2 results
Best Sellers
Water Quality Guides & Tips
Learn how to maintain your filter, improve tap water quality, and choose the right filtration system for your home.
Lead Removal / Heavy Metals
Under-Sink Lead & Heavy Metal Removal Water Filters
When testing confirms elevated lead levels or other heavy metals at your kitchen faucet, a standard carbon filter usually isn’t built to handle it. This under sink water filter lead removal category adds dedicated heavy-metal removal media on top of Gen4 Advanced filtration, connecting directly to your cold-water valve beneath the sink. It’s built for households that need more than general-purpose contaminant reduction at the faucet, since ordinary carbon media isn’t tested or rated for lead the way this dedicated media is. If a test comes back showing lead above what you’re comfortable with, this category is the place to start rather than a general-purpose under-sink filter, and every model here is built around that one job: bringing lead and related heavy metals down to levels that meet recognized removal standards, not just improving taste and odor. Households on well water with known plumbing-related lead, along with anyone in an older home with lead solder or fixtures, are the households this category is designed for.
What Removal Efficiency Means
“Removal efficiency” describes how much of a given contaminant a filter reduces under tested conditions, usually expressed as a percentage. For lead, third-party testing, WQA for the base Gen4 media and CLB Labs for the added heavy-metal component, establishes those figures under standardized protocols rather than manufacturer estimates, so performance can be compared across models on equal footing. Several of these products are rated against EPA maximum contaminant levels for lead, which gives you a recognized benchmark to check tested figures against rather than taking a removal claim on faith. Every product in this category lists its tested removal efficiency on its spec sheet, along with which lab produced the figure and which contaminants it covers, so you can compare listings side by side before choosing.
Single-Stage or Dual-Stage?
We offer both single-cartridge combo filters, which blend heavy-metal media with Gen4 Advanced in one unit, and two-cartridge systems, which use a separate, independently sized heavy-metal cartridge alongside Gen4. If your test shows moderate elevated levels, a single-cartridge combo is often enough; for higher or more severe contamination, the two-cartridge option’s independently sized removal media offers more capacity before a cartridge needs swapping. Comparing the two on their spec sheets, tested removal percentage, rated capacity, and recommended cartridge life, is the fastest way to decide which fits your situation, and either configuration installs the same way underneath the sink.
Getting It Installed
Every system in this category uses direct-connect faucet installation at your existing cold-water shutoff valve, with no drilling into countertop or cabinetry and typically no plumber required. The process is identical whichever configuration you choose, so any under sink water filter lead removal model in this range installs the same way, only the cartridge count underneath the sink changes. Most households have a unit connected and running within about thirty minutes using basic hand tools, and swapping a cartridge later takes only a few minutes once the initial connection is in place.
Frequently Asked Questions
How effective are under-sink filters at removing lead?
Effectiveness depends on the specific media and cartridge configuration. Our combo and two-cartridge lead-removal filters are tested by WQA for the base Gen4 media and CLB Labs for the added heavy-metal component, with tested removal figures published on each product’s spec sheet.
What’s the difference between single-stage and dual-stage lead removal?
A single-cartridge combo filter blends heavy-metal removal media with Gen4 Advanced in one unit. A two-cartridge system uses a separate, independently sized heavy-metal cartridge alongside Gen4, giving more capacity for higher or more severe contamination levels.
How is this filter installed under the sink?
It connects directly to your existing cold-water shutoff valve through a direct-connect fitting, with no drilling required and typically no plumber needed.
One small flag: the technical spec sheet actually lists the keyword as “under sink water filter for lead removal” (with “for”). I used your exact wording without “for” per this message, just noting the mismatch in case it matters for whoever checks this against the spec file.
